MFD Verified Fitment

My Fireplace DoorsFitment · doors · care

MFD Verified Fitment

Find the right fit before you buy.

Send clear photographs of the fireplace, record the measurements, and tell us which door you are considering. MFD compares the evidence before approving the fitment.

If anything conflicts, we pause and ask for what is missing. We do not guess with your order.

Get started Five guided steps. Photos and measurements.

Choose the responsible path

Choose your path.

Verified Fitment is optional and is not required to buy. It adds MFD review and a written decision. Independent Purchase leaves identification, compatibility, measurements, configuration, and fitment with the buyer.

Independent Purchase

You remain free to shop independently.

MFD will not represent the product as verified. You accept responsibility for fireplace identification, compatibility, measurements, configuration, and fitment. Ordinary product, fulfillment, shipping-damage, and manufacturer warranty protections still apply. This path does not authorize a prohibited or unsafe installation.

Continue to Fireplace Doors

ProjectIdentifyPhotographMeasureReview

Leave empty

Step 1 of 5

Begin the project record.

Tell us who you are, where the fireplace is, and what you hope to purchase. Have your phone and a rigid tape measure ready. Photo uploads open in Step 3. Typed answers are saved on this device as you work.

1 Start2 Describe3 Add photos4 Measure5 Review

Your name

Email address

Best phone number

Project city and state

Product being considered (optional)

What are you trying to accomplish? *

Step 3 of 5

Add your fireplace photos.

Tap each photo control below and use your camera or photo library. A preview and checkmark will confirm every photo. Use current, well-lit photographs taken while the fireplace is completely cool and unlit.

The entire fireplace

Include the wall, hearth, mantel, surrounding construction, and anything that may obstruct installation

Add this required photo

Straight-on opening

Center the camera. Show the entire opening, face, hearth relationship, vents, louvers, trim, and controls

Add this required photo

Firebox and mounting surfaces

Show the lintel, returns, lower edge, mounting surfaces, tracks, brackets, and the transition to the facing

Add this required photo

Manufacturer rating plate

Show the complete label and make the manufacturer, model, serial, and listing information readable.

Rating plate photograph

If it cannot be located safely, your selection in Step 2 documents that fact.

Additional condition photographs (optional, up to 8)

Step 4 of 5

Measure so the evidence can be checked.

Use a rigid metal tape. Measure width across the top, center, and bottom, then height at the left, center, and right. Enter the whole inches and fraction actually shown for each position. The form also records both diagonals. These measurements begin the identification record. If a specific product requires additional evidence, MFD will request the exact measurement photographs needed during product-specific verification.

Do not round, average, use a phone measuring app, or rely on plans or an old measurement. Preserve the smallest dimension; MFD will decide which value controls for the selected product.

Opening width at the top

Whole in.

Fraction

Center width across the middle

Whole in.

Fraction

Opening width at the bottom

Whole in.

Fraction

Opening height at the left

Whole in.

Fraction

Opening height at the center

Whole in.

Fraction

Opening height at the right

Whole in.

Fraction

Upper-left to lower-right diagonal

Whole in.

Fraction

Upper-right to lower-left diagonal

Whole in.

Fraction

Representative opening depth

Face to front of lintel

Flat facing above opening

Flat facing left

Flat facing right

Flat or usable area below

Hearth projection

Nearest obstruction clearance

Measurement and mounting notes

Step 5 of 5

Review before submitting.

This check can identify contradictions, but it does not grant approval. MFD must compare the complete evidence with the exact proposed product and controlling manufacturer requirements.

I confirm that these photographs are current, the measurements were taken from the physical fireplace, the entered values match the tape, and I have disclosed planned changes. I understand this submission begins review and is not fitment approval.

I authorize My Fireplace Doors LLC to retain this evidence as part of my project and fireplace record and to contact me about the review.

Create my free My Fireplace and save this project to it. I can return securely, track the review, and keep future fireplace records together.

Arched, angled, uneven, or changing opening?

Do not average it. Let MFD identify the controlling points.

See the difficult-opening process

The MFD My Fireplace record

One fireplace. One living record. One decision that follows the order.

Fireplace record

Measurements, photographs, identity, conditions, and every later revision stay connected to the same fireplace.

Written fitment decision

MFD reviews your fireplace details against the manufacturer’s requirements and names the exact product and options approved for your project.

Your approved order

Your approved photographs, measurements, product choices, and permission to proceed are saved with the order, so later profile changes do not replace its record.

The fireplace remains the source of truth from first photograph through final order.

Choose your path.

Begin the project record.

Describe what you can see.

Add your fireplace photos.

The entire fireplace

Straight-on opening

Firebox and mounting surfaces

Manufacturer rating plate

Measure so the evidence can be checked.

Review before submitting.

Fireplace record

Written fitment decision

Your approved order

Your fireplace. Your account.

How would you like to begin?

Shop the entire store.

Shopping for fireplace doors?

Your fireplace. All in one place.